UnrealIRCd Forums

Can anyone show me what it looks in the services.conf when setting up the DefCon? I tried to once, and it shut down my services completely saying it was missing Defcon levels 1-4. I don't want to mess up again and shut down services, so can someone please show me what it looks like when correctly set up? Especially the 1-4 levels

Thanks

Defcon is a services feature, moving this post to the appropriate forum.

I just need basically - to know where exactly I take out the #'s.




DefCon configuration
#
###########################################################################

# DefConLevel <level> [OPTIONAL]
# Default defcon level (1-5) to use when starting services up, level 5
# instructs services to run as normal.

#DefConLevel 5

# DefCon1-4 <numeric> [REQUIRED if Defcon is activated]
# These numercics determine which of the following operations take place
# at each level, the correct numeric can be found by adding together the
# number for each restriction you wish to place at a level.
# No new channel registrations 1
# No New Nick Registrations 2
# No MLOCK changes 4
# Force Chan Mode 8
# Use Reduced Session Limit 16
# KILL any new clients trying to connect 32
# Services will ignore everyone but opers 64
# Services will silently ignore everyone but opers 128
# AKILL all new clients trying to connect 256
# No new memos sent to block memoserv attacks 512

#DefCon4 23
# No channel reg + No Nick Reg + No MLOCK changes + Use Reduced Session Limit
# 1 + 2 + 4 + 16

#DefCon3 31
# As DefCon4 + Services will Force Chan Mode's on channels
# 23 + 8

#DefCon2 159
# As DefCon3 + Services will silently ignore everyone but opers
# 31 + 128

#DefCon1 415
# As DefCon2 + AKILL all new clients trying to connect
# 159 + 256


# DefConSessionLimit <limit> [REQUIRED if DefCon is activated]
# New session limit to use when a defcon level is using "reduced"
# session limiting.
# NOTE: When using DefCon this value needs to be defined
#DefConSessionLimit 5

# DefConAkillExpire <time> [REQUIRED if DefCon is activated]
# Length of time to add the AKILL for when DEFCON is preventing
# all new clients from connecting to the network
#
# NOTE: As with all expire times, the expirey check will only be
# carried out once every "ExpireTimeout" so if this setting is
# 30m the the akill could last for 30m regardless of this setting.
#
# NOTE: When using DefCon this value needs to be defined
#DefConAkillExpire 5m

# DefConChanModes <modes> [REQUIRED if DefCon is activated]
# The channel modes to set on all channel's when the DefCon channel
# mode system is in use.
#
# NOTE: Choose these modes carefully, because when defcon switches to
# a level which does NOT have the mode setting selected, services will
# set the reverse on all channel's, e.g. if this setting is +RN
# when defcon is used all channel's will be set to +RN, when
# defcon is removed, channels will all be set to -RN. You don't
# want to set this to +k for example because when defcon is removed all
# channels will -k.
# NOTE: mlock'ed modes will not be lost
#DefConChanModes "+R"

# DefConTimeOut <time> [OPTIONAL]
# This value can be used to automatically return the network to
# defcon 5 after the specified time period - just in case any opers
# forget to remove a defcon setting.
#DefConTimeOut 30m

# GlobalOnDefcon [OPTIONAL]
#
# Setting this directive will make Services send a global message on
# Defcon Level changes.
#GlobalOnDefcon

# GlobalOnDefconMore [OPTIONAL]
#
# Setting this directive will make Services send a global message on
# Defcon Level changes. Uncommenting this will allow you to send along
# with the new level, the DefconMessage.
#GlobalOnDefconMore

#DefconMessage "Put your message to send your users here. Dont forget to uncomment GlobalOnDefconMore"

# DefConOffMessage [OPTIONAL]
#
# If this is defined, it will be used in place of GlobalOnDefcon and
# GlobalOnDefconMore when defcon is returned to level 5
#DefConOffMessage "Services are now back to normal, sorry for any inconvenience"

# DefConAkillReason <text> [REQUIRED if DefCon is activated]
#
# When using DEFCON this setting will be used when any clients are killed
# or akilled from the network by defcon
#
#DefConAkillReason "This network is currently not accepting connections, please try again later"


~~~~~~~~